Options
Dr. Ramírez-Arias, Guillermo
Nombre de publicación
Dr. Ramírez-Arias, Guillermo
Nombre completo
Ramírez Arias, Guillermo Esteban
Facultad
Email
guillermoramirez@ucsc.cl
ORCID
5 results
Research Outputs
Now showing 1 - 5 of 5
- PublicationModeling and evaluation of paper machine coater sections part 1: 1-coater section and tension setpoints(IEEE Transactions on Industry Applications, 2019)
; ;Valenzuela, M. Aníbal ;Pittman, Steve D.Lorenz, Robert D.Coater sections are challenging to tune during the commissioning of a paper machine. This paper presents a detailed mechanical-electrical model of a 1-coater section, which includes a linear, operating point model of the sheet in the different spans, all the drivetrain components, and the vector-controlled ac drives. The sheet model considers tail widening as well as the effect of coating and drying on the sheet elastic constant, activation of the torque current control, and the beginning of coating. The developed model allows for complete evaluation of the different transient events including paper slack due to load impacts. Results show that the best performance of the drives is obtained operating the spans with even sheet tensions, which reduces and/or eliminates the operation of the drives in regeneration or braking zones. © 1972-2012 IEEE. - PublicationIdentification of impact frequency for down-the-hole drills using motor current signature analysis(Applied Sciences, 2023)
;Brito, Diego ;Gómez, René ;Carvajal, Gonzalo ;Reyes-Chamorro, LorenzoIn rotary-percussion drilling, the impact frequency is a crucial variable that is closely linked to operational factors that determine the efficacy of the drilling process, such as the rate of penetration, bit wear, and rock mass characteristics. Typical identification methods rely on complex simulation models or the analysis of different sensor signals installed on specially adapted setups, which are difficult to be implemented in the field. This paper presents a novel study where the impact frequency is identified by motor current signature analysis (MCSA) applied to an induction motor driving a DTH drilling setup. The analysis of the case study begins with the definition of characteristic drilling stages where the pressure and sound signals allow the detection of an impact frequency of 14.10 Hz, which is then used as a reference to validate three MCSA identification approaches. As a result of the analysis, the envelope approach is the most robust for nearly real-time implementations considering its simplicity and range of coverage. Experimental results provide evidence about the feasibility of the proposed MCSA methods to be integrated into Measurement-While-Drilling (MWD) systems to improve drilling condition monitoring and rock mass characterization. - PublicationElectro-Mechanical modeling and evaluation of electric load haul dump based on field measurements(Energies, 2023)
;Freire, Gabriel; ;Gómez, René ;Skrzypkowski, KrzysztofZagórski, KrzysztofIn underground mining, conventional loader equipment uses diesel as a power source, implying different drawbacks, such as combustion gases, low visibility, worker’s health problems, and high ventilation requirements. Thus, hybrid and electric loaders are being developed by the main industry suppliers who prefer clean technology. In this study, we analyzed the performance of an electro-mechanical powertrain through a dynamic model of underground-loader equipment using field data. This electric LHD model was compared to a diesel loader under the same operational conditions. For the case study, the results showed that the proposed electro-mechanical model, considering 14 tons of capacity, consumed 86.8 kWh, representing 60.5% less energy than the diesel loader with similar speed and torque characteristics. Thus, the proposed methodology is a valuable tool for operators, process engineers, and decision-makers, allowing an energy-efficiency evaluation for electric LHD adoption, based on the current operational data available for conventional equipment. - PublicationModeling and evaluation of paper machine coater sections part 2: 2-coater section and control loops' bandwidth(IEEE Transactions on Industry Applications, 2019)
; ;Valenzuela, M. Aníbal ;Pittman, Steve D.Lorenz, Robert D.Coater sections are examples of multi-span web transporting systems, with dynamic characteristics related to the sheet properties and control schemes. This paper first describes and analyzes a set of field records of a production 2-coater section paper machine. Then, extending the 1-coater section model developed in a related paper, a precise simulation model of a 2-coater section is implemented. This model is used to evaluate the beginning of the coating process and the effect on the section responses of different bandwidth settings in the tension and speed controllers. Results show agreement with the field records and demonstrate that the developed model is a powerful tool to analyze and understand the behavior of coater sections during both transient and steady-state conditions. - PublicationExpert system for the detection of condensate accumulation inside dryer cylinders during section startingThe presence of condensate inside the dryer cylinders of a paper machine produces a significant increase in the power required to accelerate the section, risking a drive overload and / or section shutdown. In previous works, the authors developed a robust estimation algorithm for the condensate power and a generalized correlation for the estimation of condensate loads in industrial dryer cylinders up to 55 [mm] of condensate rim. This paper presents and evaluates a rule-based expert system (ES) capable of detecting the presence and amount of condensate in up to three groups of cylinders with different condensate loads. The ES can give an early warning message to the operators, and determine the condensate load and number of cylinders within each group. Evaluation is done using a combined condensate load for a fictitious 1500-mm, 8 cylinder dryer section. Results show the capacity of the developed ES to give early warning, as well as a correct estimation of the condensate loads and numbers of cylinders involved.